How To Fix Restore Point Problems In Windows 10?

If you have a severe problem with Windows 10, you should use System Restore to fix it by reverting your machine to a previous restore point. System Restore is a really helpful tool, but customers have reported that it doesn’t work on Windows 10, which we’ll remedy today. If your PC’s System Restore isn’t working, you can get this error. This is most likely to happen if the restore point is broken or corrupted in some way.

If this is the case, you may receive the message “System Restore did not complete successfully”. In other issues, you might observe that the System Restore tool gets stuck in midpoint or the utility shuts down automatically. These are only a few of the problems that can arise, but perhaps this guide will assist you in resolving issues with system restore point in Windows 10.

How To Fix Restore Point Problems In Windows 10?

Here are a few ways to fix issues with the system restore point in Windows 10.

Method 1: Check Hard Disk Space

System Restore requires at least 300MB of space for each partition with System Restore enabled to function effectively. Check the amount of free space you have and adjust the space needed by System Restore Point.

Step 1: To create a restore point, press Windows Key + S and type Create a restore point.

Step 2: From the list of options, select Create a restore point.

Step 3: Select a hard drive partition and click Configure when the System Properties box appears.

Step 4: Adjust the amount of space used by System Restore by dragging the slider.

Method 2: Temporarily Disable Antivirus

Antivirus software has improved throughout time to ensure that it detects both potential threats and viruses and malware that have been updated on the virus definition list. As a result, any application that consumes a lot of resources is potentially dangerous, and this is why there can arise a conflict between the System Restore Tool and your Antivirus.

To rule out this scenario, turn off your antivirus software for a few minutes and observe if you can create a system restore point  on Windows 10. If your system restore point issues are resolved then your antivirus is the culprit here. The solution to fix this issue differs depending on the antivirus program and can be found in the software’s instructions or by calling support.

Method 3: Run Chkdsk Command

The chkdsk command, which stands for “check disk,” is a Command Prompt command that checks a specific disk and, if necessary, repairs or recovers data on the drive. Chkdsk also labels any damaged or malfunctioning sectors on the hard drive or disc as “bad,” and recovers any data that is still usable. Here are the steps to initiate this command:

Step 1: Choose Command Prompt (Admin) from the menu by pressing Windows Key + X.

Step 2: When the Command Prompt window appears, type the following into it and hit Enter:

chkdsk /f /r X:

Step 3: Replace X with the letter that corresponds to a hard disk partition on your computer.

Step 4: Because corrupted files and folders on your disk can cause restore points to fail, you may need to inspect your hard drive to fix the corrupted data.

Step 5: Be patient as this process can take a long time. You may have to restart your computer to finish the disc scan.

Method 4: Perform SFC

The System File Checker can be used to scan Windows and recover your data if some Windows operations aren’t working or if Windows crashes. Here are the steps:

Step 1: Select Command Prompt (Admin) from the menu by pressing Windows Key + X.

Step 2: To run it, type the following into Command Prompt and hit Enter:

sfc /scannow

Step 3: Wait for the process to finish as you follow the instructions.

Step 4: If your Windows 10 is corrupted, System Restore may not operate properly, and you’ll need to run the SFC scan to fix it.

Method 5: Windows Services

Windows Operating System has a lot of services that run in the background to ensure that users get an infallible experience. Here are the steps to check Windows Service related to System Restore:

Step 1: Type services.msc by pressing Windows Key + S. Click OK or press Enter.

Step 2: Locate the following services when the Services window appears –

• Volume Shadow Copy
• Task Scheduler
• Microsoft Software Shadow Copy Provider Service
• System Restore Service.

Step 3: Make sure that the Startup type is set to Automatic and the Service status is set to Running when you double-click any of these services.

Step 4: To save your changes, click Apply and OK and then shut the Services window and restart your computer,

Method 6: Use Safe Mode

Safe mode begins Windows in a minimal form, with only a few files and drivers installed. If a problem does not occur in safe mode, it is unlikely that the issue is caused by default settings or basic device drivers.

Step 1: Click on the Power button in the Start Menu.

Step 2: Hold down Shift and press the Restart button on your keyboard.

Step 3: Choose Troubleshoot > Advanced options > Startup Settings and Restart when your machine restarts.

Step 4: Press F5 to select Safe Mode with Networking when your computer restarts.

Step 5: Attempt a System Restore after entering Safe Mode.

Because certain applications can cause errors while using System Restore, it’s recommended that you use Safe Mode to restore your system.

Method 7: Modify Registry

The registry, often known as the Windows Registry, is a database that contains information, settings, options, and other variables for software and hardware installed on all versions of Microsoft Windows.

Step 1: Open Registry Editor by going to Search and typing regedit.

Step 2: Go to the following registry path:

HKEY_LOCAL_MACHINESOFTWAREMicrosoftWindows NTCurrentVersionScheduleTaskCache

Step 3: To begin, make a backup of the TaskCache registry key. Select Export from the context menu of TaskCache by right-clicking it.

Step 4: Enter a name for the backup file, choose a location for it, and save it.

Step 5: Then, in the Registry Editor, go to this key.

HKEY_LOCAL_MACHINESOFTWAREMicrosoftWindows NTCurrentVersionScheduleTaskCacheTreeMicrosoftWindows

Step 6: On the context menu of the Windows key, right-click it and select Delete.

Step 7: To confirm, press the Yes button, and then close the Registry.

Step 8: Reboot the Computer.

Method 8: Run DISM

DISM stands for Deployment Image Servicing and Management, and it’s a command-line utility for servicing Windows images. To mount and receive information about a Windows image file, use the DISM image management commands. Here are the steps to run DISM:

Step 1: Search for cmd, then right-click on the Command Prompt and select Run as Administrator.

Step 2: Copy-paste the following lines one by one into the command line, pressing Enter after each:

DISM /online /Cleanup-Image / ScanHealth

DISM /Online /Cleanup-Image /RestoreHealth

Step 3: Wait until the process is completed before proceeding.

Step 4: Restart your computer.

The Final Word On How To Fix Restore Point Problems In Windows 10?

System Restore Point is an important feature of the Windows operating system that helps to restore your computer to a stable software state in case of a system crash or corruption. The above methods will help you ensure that your System Restore Tool is free from all issues and you can safely create a system restore point.

Follow us on social media – Facebook, Instagram, and YouTube. For any queries or suggestions, please let us know in the comments section below. We would love to get back to you with a solution. We regularly post tips and tricks, along with answers to common issues related to technology.